Power Supplies & Accessories

Accessories we Provide:

Power Supplies

We carry  a variety of power supplies for servo or stepper drives ranging from 300W continuous to over 35kW peak power. Selecting the correct power supply is as simple as specifying the correct voltage and picking a model that can supply enough power.

Isolation is also an important consideration for safe and reliable operation of the drive. Isolation takes the form of optical isolators that isolate the signal ground from the power ground.

In the power supply, isolation takes the form of an isolation transformer that isolates the input AC from the power supply output. If the drive datasheet does not specify optical isolation then you must use a power supply with an isolation transformer.

Click on the following link to view our complete Power Supply Product Catalog.

Sensor Accessories

A sensor rarely comes unaccompanied: accessories supporting their mounting, commissioning, and use are of considerable importance for the reliable functioning of an automation solution. The characteristic practical orientation of SensoPart products is thus also evident in a particularly versatile and user-friendly range of accessories. This includes lighting, cables, mounting, reflectors and more. 

Filter Cards

We also carry filter cards, used to ensure current loop stability,  A minimum load inductance is essential for the proper operation of PWM servo drives. If the load inductance is less than the minimum rating for the servo drive, Filter Cards can be used to add inductance to the motor/drive system.

For example, if the servo drive datasheet calls for a minimum inductance of 250uH, and your motor only has 25uH, then the addition of the BFC15030 will ensure proper operation. The total inductance for the motor and filter card will be 25uH + 300uH = 325uH.

Inductive filter cards are also used to reduce the PWM switching noise that occurs with high power supply voltages (>250VDC) and long cable runs (>10m).  FC filter cards are designed for use with brush type servo motors, voice coils and other single phase loads. BFC filter cards are designed for use with brushless servo motors, linear motors and other three-phase loads.

Shunt Regulators

If you are having transient over-voltage problems, please look at our available shunt regulators. These simple devices increase system reliability by stabilizing voltage fluctuations, thereby eliminating over-voltage shutdowns.

The need for a shunt regulator is indicated when system faults occur during the deceleration portion of a move. This can be verified by monitoring the power supply voltage on an oscilloscope and looking for voltages that exceed the over voltage rating of the servo drive.

Regen Clamps

Many motor and drive systems require a clamp circuit to limit increases in power supply voltage when the motor is decelerating under load. This is commonly referred to as "regeneration", and occurs when DC motors are driven by their load (backdriving). During regeneration the DC motor can produce enough voltage to actually exceed the input power supply voltage.

Applied Motion drives can deal with regeneration by channeling the increased motor voltage back to the source power supply. However, if the voltage is not clamped to a safe level the power supply and/or drive can be damaged or destroyed. 50 Watt continuous, 800 Watt peak rating.

Here is the link to the complete Regen Clamp catalog.


Items 1-30 of 165

per page
Set Descending Direction
  1. 1000-382

    PoE Midspan injector designed to supply power over Ethernet to compatible integrated motors

  2. 3004-190 Accessories Applied Motion Products


  3. ADP-1 Accessories Dyadic Systems

    Adaptor Board

  4. ADP-2-4 Accessories Dyadic Systems

    Adaptor Board

  5. BFC10010 Accessories Advanced Motion Controls

    Filter Card

  6. BFC15030 Accessories Advanced Motion Controls

    Filter Card

  7. BOB1 Accessories Applied Motion Products

    Breakout Board

  8. BOB2 Accessories Applied Motion Products

    Breakout Board

  9. BOB2 Accessories Applied Motion Products

    Breakout Board for SV200 I/O Connector

  10. CTA-23-EN-SET Accessories Dyadic Systems

    Teach Pendant

  11. DESUNIWINCD6 Accessories Exor Electronic

    Programming Software

  12. FC10010 Accessories Advanced Motion Controls

    Filter Card

  13. FC1010 Accessories Advanced Motion Controls

    Filter Card

  14. FC15030 Accessories Advanced Motion Controls

    Filter Card

  15. FT001 Accessories Dyadic Systems


  16. fT001 Accessories Dyadic Systems


  17. KC-23AMPSEAL01 Accessories Advanced Motion Controls

    Mating Connector

  18. M12 5pin-A Female+10m PUR Cable
    M12 5pin-A Female+10m PUR Cable

    M12 5pin Connection Cable, 10m, IP67, PUR

  19. M12 5pin-A Female+2m PUR Cable
    M12 5pin-A Female+2m PUR Cable

    M12 5pin Connection Cable, 2m, IP67, PUR

  20. M12 5pin-A Female+5m PUR Cable
    M12 5pin-A Female+5m PUR Cable

    M12 5pin Connection Cable, 5m, IP67, PUR

  21. M12 8pin-A Female+10m PUR Cable
    M12 8pin-A Female+10m PUR Cable

    M12 8pin Connection Cable, 10m, IP67, PUR

  22. M12 8pin-A Female+2m PUR Cable
    M12 8pin-A Female+2m PUR Cable

    M12 8pin Connection Cable, 2m, IP67, PUR

  23. M12 8pin-A Female+5m PUR Cable
    M12 8pin-A Female+5m PUR Cable

    M12 8pin Connection Cable, 5m, IP67, PUR

  24. MC1XAZ01 Accessories Advanced Motion Controls

    Mounting Card

  25. MC1XAZ01-HR Accessories Advanced Motion Controls

    Mounting Card

  26. MC1XDZC02 Accessories Advanced Motion Controls

    Mounting Card

  27. MC1XDZC02-HP1 Accessories Advanced Motion Controls

    Mounting Card

  28. MC1XDZC02-QD Accessories Advanced Motion Controls

    Mounting Card

  29. MC1XDZPC01 Accessories Advanced Motion Controls

    Mounting Card

  30. MC1XDZPE01 Accessories Advanced Motion Controls

    Mounting Card


Items 1-30 of 165

per page
Set Descending Direction