Motion & Automation Controllers
A motion control system is a system that controls the position, velocity, force or pressure of some machine. As an example, an electromechanical based motion control system consists of a motion controller (the brains of the system), a drive (which takes the low power command signal from the motion controller and converts it into high power current/voltage to the motor), a motor (which converts electrical energy to mechanical energy), a feedback device (which sends signals back to the motion controller to make adjustments until the system produces the desired result), and a mechanical system (including actuators, which physically produce the desired end result).
A Motion Controller or Automation Controller is the primary intelligence, or brain, within a motion control system. It is responsible for calculating and generating the output commands for a desired motion path or trajectory. Motion controllers vary in complexity; sophisticated motion controllers typically consist of a trajectory generator (path planner), interpolator, and control loop for servo motor control.
Types of Motion Control Systems View More
Open Loop System
A system that does not use feedback to verify the desired result, or output, has been reached. Most step motor systems are operated open loop.
Closed Loop System
A system that uses feedback to verify the desired result, or output, has been reached. As an example, a feedback device such as an encoder is commonly used to provide position or velocity information to a motion controller. A servo motor system requires the use of a feedback device.
Types of Motion Controller Topologies View More
PLC based motion controllers typically utilize a digital output device, such as a counter module, that resides within the PLC system to generate command signals to a motor drive. They are usually chosen when simple, low cost motion control is required but are typically limited to a few axes and have limited coordination capabilities.
PC based motion controllers typically consist of dedicated hardware run by a real-time operating system. They use standard computer busses such as PCI, Ethernet, Serial, USB, and others for communication between the motion controller and host system. PC based controllers generate a ±10V analog output voltage command for servo control and digital command signals, commonly referred to as step and direction, for stepper control. PC based motion controllers typically are used when high axes count and/or tight coordination is required. The drawbacks of this topology include complex cabling and potentially long wiring distances between the drive and motor.
A fieldbus based motion controller topology consists of a communication interface device and intelligent drive(s). The communication interface device typically resides within a PLC or PC system and connects to a single or multiple intelligent drives. The drives contain all the functionality of the motion controller and function as a complete single axis system. Often the drives can be daisy chained to other intelligent drives on the same fieldbus. The benefits include all digital communication, detailed diagnostics, reduced cabling, high axes count and short wiring distance between the drive and motor. This topology has a higher cost especially at lower axes count and has limitations providing tight coordination for multiple axes. Examples of this topology include Profibus, DeviceNet, RS-232/485, and others.
Asynchronous vs. Deterministic Topology View More
Asynchronous communication is transmission of data, generally without the use of an external clock signal, where data can be transmitted intermittently rather than in a steady stream. Asynchronous literally means not synchronous, meaning, data is not transmitted at regular intervals, thus making possible variable bit rate, and that the transmitter and receiver clock generators do not have to be exactly synchronized all the time.
Deterministic communication is the transmission of data reaching its destination in a specific, predicable time. Time critical data transfer must be guaranteed within short and precise configurable cycles, while less critical data can be transmitted in asynchronous time slots. Data reaching its destination at guaranteed times are critical for motion control.
A deterministic bus based motion controller topology splits the motion controller functionality across a communication interface device and intelligent drive via a deterministic digital network. The communication interface device typically resides within a PLC or PC system and contains the trajectory generator. The intelligent drives typically contain the control loop and interpolator and can be daisy chained to other intelligent drives on the same network. The digital network is deterministic with low jitter to allow for tight coordination in multi axes applications. The benefits include all digital communication, detailed diagnostics, reduced cabling, high axes count, tight coordination, and short wiring distance between the drive and motor. This topology has a higher cost especially at lower axes count. Examples of this topology include EtherCAT, SERCOS, Ethernet Powerlink, PROFINET IRT, SynqNet, CANopen, and others.
Search our Motion and Automation Controllers by supplier:
Search our Motion and Automation Controller Products by subcategory at the links below:
Motion Controllers, Ethernet / USB / Network
Models include: single and multi-axis, network and stand-alone, in box-level and card-level configurations.
Learn About Ethercat / Ethernet Motion Controllers - RS232 & RS485 Controllers »
Motion Controllers, PCI, PC / 104, ISA BUS
Card level controllers feature the Accelera Series offering the highest speed & performance and the Econo Series designed for low cost.
Learn About PCI Motion Controllers - PC / 104, ISA BUS Motion Controller »
Core Modules & Embedded Products
Embedded systems designed to be faster, easier and far more accessible to people who are not trained as computer architects.
Learn About Embedded Microprocessor Core Modules - Single Board Computers »
Provides fast localized & distributed I/O handling and logic control.
Learn About I/O Controllers - Analog & Digital Input / Output Controller »