The store will not work correctly when cookies are disabled.
Please be aware we use cookies to make your experience better.A cookie is a piece of data stored on a visitor's hard drive to help us improve your access and identify repeat visitors. Cookies can also enable us to track and target the interests of our users to enhance the experience on our site. Usage of a cookie is in no way linked to any personally identifiable non-public information.Learn more.
Integrated Step Motors fuse step motor plus drive and control components into a single device. Integrated steppers offer a space-saving design that reduces wiring and saves on cost over separate motor and drive components.
Ideally suited for applications such as packaging and labeling, automated test and measurement, automated assembly and life sciences, StepSERVO™ motors from Applied Motion Products provide the next evolution integrated step motor technology.
Starting with a proven integrated motor design, we add a high-resolution incremental encoder and closed-loop servo firmware to create a motor that offers the best step motor performance available today. StepSERVO™ motors offer the same high-torque-at-low-speed and excellent holding torque characteristics of open loop stepping motors with the advantages of true closed-loop control.
These advantages include the ability to create peak torques from the motor up to 50% higher than the normal torque range of the same step motor running open loop. Closed-loop also means the motor only draws current when it needs it, so step motors now run cooler than ever before.
NEMA 11 (New!), NEMA 17 and NEMA 23 frame size motors
RS-232 or RS-485 port for programming and streaming commands
Control options including CANopen fieldbus control, digital step & direction control, analog velocity mode, streaming commands and stand-alone operation using stored Q programs.
Three motor lengths available in each frame size to provide the highest amount of torque for each length
Control options include CANopen fieldbus control, EtherNet/IP industrial networking, digital step & direction control, analog velocity mode, streaming commands and stand-alone operation using stored Q programs.
Two motor lengths available to provide both a lower torque and a higher torque option depending on application requirements
Available in NEMA 17, 23, and 24 frame sizes, including Washdown versions, combine the best of Applied Motion's drive and motor offering in a single, integrated device.
Dynamic Current Control
Anti-Resonance
Torque Ripple Smoothing
Microstep Emulation
Choose between RS-232 or RS-485 port for programming and serial communications
JVL Industri Elektronik Integrated QuickStep Stepper Motors
MIS QuickStep Stepper Motors from JVL are compact versatile Integrated stepper motors that meet almost any need for a compact stepper motor system. The force range is from 0.2 to 25Nm in flange size NEMA 17(43mm) to NEMA 43 (110mm).
The MIS motor - the complete motion solution Stepper motor with integrated controller. All necessary components in one unit.
The basic idea in the MIS motors is to minimize the installation costs but also to make a component that is much better protected against electrical noise which can be a typical problem when using long cables between controller and motor.
The stepper motor, hall sensor or encoder and electronics are specially developed by JVL so that they together form a closed unit where the power driver and controller is mounted inside the motor in a closed section.
Drive and motor fused into one NEMA 17 unit from Applied Motion Products. 18 configurations. Four control modes (R, S, Q, and CANopen). Powered directly by 12 to 48 VDC with no external drive needed.
Drive and motor fused into one NEMA 23 unit from Applied Motion Products. 20 configurations. Five control modes including EtherNet/IP and dual port EtherNet/IP. Powered directly by 12 to 70 VDC with no external drive needed.
IP65 rated NEMA 34 StepSERVO integrated motors from Applied Motion Products, combining a step motor and digital servo drive in one device. 14 configurations across Q Programming, EtherNet/IP, CANopen, and a TruCount encoder variant.
IP65 rated NEMA 24 StepSERVO integrated motors from Applied Motion Products, combining a step motor and digital servo drive in one device. 10 configurations across SCL, Q Programming, EtherNet/IP, and two TruCount absolute encoder variants.
IP40 rated with screw terminal and pluggable connectors. Combines a step motor and digital servo drive in one device. 18 configurations across Q Programming, EtherNet/IP, CANopen, and PROFINET.
Combining a step motor and digital servo drive in one device. 14 configurations across step and direction control, SCL, Q Programming, EtherNet/IP, CANopen, and a TruCount absolute encoder variant.
Combines a step motor and digital servo drive in one compact device. 6 configurations across 3 torque tiers and 2 connector styles, Q Programming over RS-485.
Fuses a step motor and drive into a single device. 8 configurations across RS-232, RS-485, EtherNet/IP, and CANopen, each available with or without an internal encoder.
Combines a step motor and digital servo drive in one device, communicating over a shared 10/100 MBit Ethernet port. 6 configurations across 3 torque tiers, SCL/Modbus TCP or EtherNet/IP.
A cookie is a piece of data stored on a visitor's hard drive to help us improve your access and identify repeat visitors. We use necessary cookies to make our site work. We'd also like to set optional cookies to help us improve it. Usage of a cookie is in no way linked to any personally identifiable non-public information. Learn More.
By clicking “Accept”, you consent to the use of ALL the cookies. However you may visit Cookie Settings to provide a controlled consent.
