Please be aware we use cookies to make your experience better. A cookie is a piece of data stored on a visitor's hard drive to help us improve your access and identify repeat visitors. Cookies can also enable us to track and target the interests of our users to enhance the experience on our site. Usage of a cookie is in no way linked to any personally identifiable non-public information. Learn more.
TSM23Q-4AG
- Buy 5 for $783.00 each and save 3%
The TSM23Q-4AG integrated StepSERVO™ is a drive+motor unit, fusing a NEMA 23 step motor and a servo drive into a single device. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. StepSERVO technology combines the high torque capabilities of a step motor with the closed loop dynamic control of a servo system. The result is a highly customizable all-in-one motion control solution that operates quietly and efficiently, requiring only the minimum amount of current to maintain commanded position and velocity. Boost torque of 25-50% higher than the rated holding torque that is available from this integrated StepSERVO motor increases the limits of acceleration, leading to faster cycle times. With software selectable servo loops that have been pre-tuned for various inertial loads, the TSM StepSERVO can be applied in systems where a traditional stepper would not be capable of achieving the high accuracy required.
The TSM23Q-4AG integrated StepSERVO can be operated in several different control modes, including Streaming Command mode using either SCL or Modbus/RTU, Pulse & Direction mode, and Velocity mode, plus it has the ability to run a Q program stored in non-volatile memory. Q programs are created using Applied Motion’s Q Programmer™ software, which provides powerful commands for motion, I/O, conditional processing, multi-tasking, math functions, and more. All TSM23 units are setup, configured and tuned using Applied Motion’s Step-Servo Quick Tuner software with built in Q Programmer. Each TSM23 integrated stepper comes with 8 digital inputs, 4 digital output, and 1 analog input. The digital inputs accept signals of 5-24 VDC and can be used for connecting pulse & direction signals, end-of-travel limit switches, jog switches, quadrature encoder signals, PLC outputs, sensors, or many other signal types. The digital outputs can be connected to PLC inputs, counters, lights, relays, or other devices. The analog input accepts 0-5 VDC signals and can be used for velocity and position control.
The TSM23Q-4AG comes with an RS-232 port for programming and serial communications to allow for the use either Modbus/RTU or Applied Motion’s Streaming Command Language (SCL). An integral 5000-line (20,000 count/rev) incremental encoder is housed inside the same enclosure as the drive electronics and used for closed-loop servo control to attain highly accurate position and velocity control. Encoder counts can be accessed over the network or from within the Q program using SCL registers.
Features
Manufacturer | Applied Motion Products |
---|---|
Communication/Interface | RS-232 |
Max Holding Torque (mNm) | 2,401.00 |
Max Holding Torque oz (in) | 340.00 |
Max Length (mm) | 87.00 |
Min Operating Temperature (°C) | 0.00 |
Min Operating Temperature (°F) | 32.00 |
Max Operating Temperature (°C) | 85.00 |
Max Operating Temperature (°F) | 185.00 |
Shaft Diameter (mm) | 8.00 |
Shaft Diameter (in) | 0.32 |
Max Input Supply Voltage (VDC) | 70.00 |
Motor Construction | Hybrid Stepper |
NEMA Frame Size | 23 |
Number of Axes | 1 |
Operating Mode | Analog Positioning, Analog Torque / Velocity, Encoder Following, Q Programming, Streaming Commands, Velocity Control, Modbus RTU |
Rotor Inertia (kg-m-s²) | 4.90E-05 |
Rotor Inertia (oz-in-s²) | 6.94E-03 |
Setup | Software Setup |
Shaft Orientation | In-line,Single-nded |
Step Angle (°) | 1.8 |
Sample image only. Product may differ