Analog Type Amplifiers

Analog Type Amplifiers

Advanced Motion Controls' family of brush and brushless Analog Servo Drives provides unparalleled benefits in both simplicity and performance. Drive setup and operation is more straightforward than digital drives, while achieving higher bandwidth and faster response times at a lower cost. Analog drive technology has been a staple of servo system solutions since day one, and our years of experience in building the highest quality products has created a solid and continuously improving selection of analog drives. A variety of command options, including ±10V analog, PWM and Direction, dual Sine wave, and specialized electric vehicle commands make the Advanced Motion Controls' family of analog drives your best choice for proven servo solutions. All AMC's Analog Servo Drives feature:

  • Built-in hardware protection – Over Current, Over Voltage, Over Temperature, Short Circuit
  • DIP Switches and Potentiometers for loop tuning, current limit adjustments, and drive configuration
  • Standard models for both brushed and brushless motor varieties
  • Velocity feedback provided by incremental encoder, Hall Sensors, or tachometer
  • Analog Position Loop control available
  • Optical Isolation between high and low power signals standard on most models
  • Current, Velocity, and Fault Monitor analog output signals
  • Status LEDs for power and drive status
    • Standard models in both Panel Mount, PCB Mount (Z-Drives), and Vehicle Mount (M/V™ Series Motor Controllers)
    • Four quadrant regenerative operation
    • Extended Environment versions available (AZX series Z-Drives)

µZ Plug-In Drives

µZ’s are the smallest off-the-shelf servo drives from ADVANCED Motion Controls.  Pronounced ‘Micro-Z’ these plug-in drives are designed for embedded applications in a wide range of industries including: Robotics, Lab Automation, Homeland Security/Military, Electric Mobility, Medical and Packaging.

µZ servo drives are designed to drive brushless and brushed DC motors at a high switching frequency.  To increase system reliability and to reduce cabling costs, the drives are designed for direct integration into your PCB.  Weighing in at less than 9 grams, µZ Drives output 10A peak and 5A continuous and operate with a bus voltage range of 10-36VDC.

Designed without the need for a heatsink, the µZ’s are true featherweights with a high power to weight ratio.  The µZ’s are fully protected against over-voltage, under-voltage, over-current, over-heating, and short-circuits. Depending on the model, the drives interface with digital controllers that have analog ±10V or PWM/Direction commands. These servo drives require only a single unregulated isolated DC power supply, and are fully RoHS (Reduction of Hazardous Substances) compliant.

 Features:

  • Designed for direct board-to-board integration.AMC UZ Graphic
  • No heatsink and no need for additional heatsinking results in the smallest installed volume
  • No heatsink and no need for additional heatsinking results in the smallest installed volume
  • Feather weight, less than 9 grams
  • Dimensions (mm) 38.1 x 38.1 x 7.34 for current mode models, 43.2 x 38.1 x 9.4 for velocity / duty cycle models
  • Dimensions (in) 1.50 x 1.50 x 0.29 for current mode models, 1.70 x 1.50 x 0.37 for velocity / duty cycle models
  • Large operational temperature range, 0-85°C
  • Compatible with low inductance motors
  • Smallest form factor of any off-the-shelf servo drive from ADVANCED Motion Controls
  • 40 kHz switching frequency

Downlaod AMC's complete family of cost-effective Analog Servo Drives catalog

Datasheets and Support:View More

  • AZB10A4 for ±10V Command Signals, Current Mode
  • AZBH10A4 for ±10V Command Signals, Hall Velocity Mode
  • AZBE10A4 for ±10V Command Signals, Encoder Velocity Mode
  • AZBD10A4 for ±10V Command Signals, Duty Cycle Mode
  • AZBDC10A4 for PWM/Direction Command Signals

Stand-alone (drives with built-in interface)

  • AZB10A4IC for ±10V Command Signals, Current Mode
  • AZBDC10A4IC for PWM/Direction Command Signals
  • AZBE10A4IC for ±10V Command Signals, Encoder Velocity Mode
  • AZBH10A4IC for ±10V Command Signals, Hall Velocity Mode
  • AZBD10A4IC for ±10V Command Signals, Duty Cycle Mode






1 Item

per page
Set Descending Direction
Filter By
  1. AZ60A8 Amplifiers Analog Type Advanced Motion Controls
    AZ60A8

    10-80 VDC Input; 30A continuous / 60A peak | 2.3kW Output @ 80 VDC in

1 Item

per page
Set Descending Direction