Analog Servo Drive Amplifiers

Advanced Motion Controls' family of brush & brushless Analog Servo Drives & Motors provides unparalleled benefits in both simplicity and performance. Drive setup and operation is more straightforward than digital drives, while achieving higher bandwidth and faster response times at a lower cost. Analog drive technology has been a staple of servo system solutions since day one, and our years of experience in building the highest quality products has created a solid and continuously improving selection of analog drives. A variety of command options, including ±10V analog, PWM and Direction, dual Sine wave, and specialized electric vehicle commands make the Advanced Motion Controls' family of brush & brushless analog servo drives your best choice for proven servo solutions. 

All AMC's Analog Servo Drives feature:

  • Built-in hardware protection – Over Current, Over Voltage, Over Temperature, Short Circuit
  • DIP Switches and Potentiometers for loop tuning, current limit adjustments, and drive configuration
  • Standard models for both brushed and brushless motor varieties
  • Velocity feedback provided by incremental encoder, Hall Sensors, or tachometer
  • Analog Position Loop control available
  • Optical Isolation between high and low power signals standard on most models
  • Current, Velocity, and Fault Monitor analog output signals
  • Status LEDs for power and drive status
    • Standard models in both Panel Mount, PCB Mount (Z-Drives), and Vehicle Mount (M/V™ Series Motor Controllers)
    • Four quadrant regenerative operation
    • Extended Environment versions available (AZX series Z-Drives)

µZ Plug-In Drives

µZ’s are the smallest off-the-shelf servo drives from ADVANCED Motion Controls.  Pronounced ‘Micro-Z’ these plug-in drives are designed for embedded applications in a wide range of industries including: Robotics, Lab Automation, Homeland Security/Military, Electric Mobility, Medical and Packaging.

µZ servo drives are designed to drive brushless and brushed DC motors at a high switching frequency.  To increase system reliability and to reduce cabling costs, the drives are designed for direct integration into your PCB.  Weighing in at less than 9 grams, µZ Drives output 10A peak and 5A continuous and operate with a bus voltage range of 10-36VDC.

Designed without the need for a heatsink, the µZ’s are true featherweights with a high power to weight ratio.  The µZ’s are fully protected against over-voltage, under-voltage, over-current, over-heating, and short-circuits. Depending on the model, the drives interface with digital controllers that have analog ±10V or PWM/Direction commands. These servo drives require only a single unregulated isolated DC power supply, and are fully RoHS (Reduction of Hazardous Substances) compliant.

Features:

  • Designed for direct board-to-board integration.AMC UZ Graphic
  • No heatsink and no need for additional heatsinking results in the smallest installed volume
  • No heatsink and no need for additional heatsinking results in the smallest installed volume
  • Feather weight, less than 9 grams
  • Dimensions (mm) 38.1 x 38.1 x 7.34 for current mode models, 43.2 x 38.1 x 9.4 for velocity / duty cycle models
  • Dimensions (in) 1.50 x 1.50 x 0.29 for current mode models, 1.70 x 1.50 x 0.37 for velocity / duty cycle models
  • Large operational temperature range, 0-85°C
  • Compatible with low inductance motors
  • Smallest form factor of any off-the-shelf servo drive from ADVANCED Motion Controls
  • 40 kHz switching frequency
 

Resources

  • AZB10A4 for ±10V Command Signals, Current Mode
  • AZBH10A4 for ±10V Command Signals, Hall Velocity Mode
  • AZBE10A4 for ±10V Command Signals, Encoder Velocity Mode
  • AZBD10A4 for ±10V Command Signals, Duty Cycle Mode
  • AZBDC10A4 for PWM/Direction Command Signals

Stand-alone (drives with built-in interface)

  • AZB10A4IC for ±10V Command Signals, Current Mode
  • AZBDC10A4IC for PWM/Direction Command Signals
  • AZBE10A4IC for ±10V Command Signals, Encoder Velocity Mode
  • AZBH10A4IC for ±10V Command Signals, Hall Velocity Mode
  • AZBD10A4IC for ±10V Command Signals, Duty Cycle Mode

Products

View as List Grid

Items 31-45 of 74

Set Descending Direction
AZBH6A8 by Advanced Motion Controls

AZBH6A8

20-80 VDCput; 3A continuous / 6A peak | 0.2kW Output @ 80 VDC

$243.00
View Details
B30A40 by Advanced Motion Controls

B30A40

60-400 VDCput; 15A continuous / 30A peak | 5.7kW Output @ 400 VDC

$843.00
View Details
AZB60A8 by Advanced Motion Controls

AZB60A8

10-80 VDCput; 30A continuous / 60A peak | 2.3kW Output @ 80 VDC

$468.00
View Details
AZBDC60A8 by Advanced Motion Controls

AZBDC60A8

10-80 VDCput; 30A continuous / 60A peak | 2.3kW Output @ 80 VDC

$468.00
View Details
AZBE60A8 by Advanced Motion Controls

AZBE60A8

10-80 VDCput; 30A continuous / 60A peak | 2.3kW Output @ 80 VDC

$491.00
View Details
AZBH25A20 by Advanced Motion Controls

AZBH25A20

40-175 VDCput; 12.5A continuous / 25A peak | 2.1kW Output @ 175 VDC

$438.00
View Details
AZBH60A8 by Advanced Motion Controls

AZBH60A8

10-80 VDCput; 30A continuous / 60A peak | 2.3kW Output @ 80 VDC

$479.00
View Details
B060A400AC by Advanced Motion Controls

B060A400AC

200-240 VAC (50/60 Hz, 3ph)put {optionally 255-373 VDC}; 30A continuous / 60A peak | 10.6kW Output @ 240 VAC

$2,465.00
View Details
B100A400AC by Advanced Motion Controls

B100A400AC

200-240 VAC (50/60 Hz, 3ph)put {optionally 255-373 VDC}; 50A continuous / 100A peak | 16.1kW Output @ 240 VAC

$2,939.00
View Details
AB15A100 by Advanced Motion Controls

AB15A100

20-80 VDC Input, 7.5 A Cont. (15 Peak)

$405.00
View Details
AB25A100 by Advanced Motion Controls

AB25A100

20-80 VDC Input, 15 A Cont. (25A Peak) Output

$430.00
View Details
AB20A200 by Advanced Motion Controls

AB20A200

40-175 VDC Input, 12 A Cont. (20 Peak) Output

$505.00
View Details
AZBD10A4 by Advanced Motion Controls

AZBD10A4

10-36 VDC Input, 5 A Cont. (10 Peak)

$177.00
View Details
AZBE10A4 by Advanced Motion Controls

AZBE10A4

10-36 VDC Input, 5 A Cont. (10 Peak)

$207.00
View Details
AZBH40A8 by Advanced Motion Controls

AZBH40A8

10-80 VDC Input, 20 A Cont. (40 Peak)

$409.00
View Details
Page
per page